Difference between revisions of "Setting up Elgg VM on CedeusGeoNode"
From stgo
(Created page with ">> return to Cedeus_IDE ---- steps performed: # copying basicubunutu1404.vdi file and renaming to elgg.vdi # creating the tilestream VM on CedeusDB (ip.18): #* <code>VBo...") |
|||
| Line 5: | Line 5: | ||
# copying basicubunutu1404.vdi file and renaming to elgg.vdi | # copying basicubunutu1404.vdi file and renaming to elgg.vdi | ||
| + | == Elgg VM setup == | ||
| + | |||
# creating the tilestream VM on CedeusDB (ip.18): | # creating the tilestream VM on CedeusDB (ip.18): | ||
#* <code>VBoxManage createvm --name elgg --ostype Ubuntu_64 --register</code> | #* <code>VBoxManage createvm --name elgg --ostype Ubuntu_64 --register</code> | ||
| Line 14: | Line 16: | ||
#*: <code>VBoxManage internalcommands sethduuid elgg.vdi</code> | #*: <code>VBoxManage internalcommands sethduuid elgg.vdi</code> | ||
#* attach the (old) disk image: | #* attach the (old) disk image: | ||
| − | #*: <code> VBoxManage storageattach " | + | #*: <code> VBoxManage storageattach "elgg" --storagectl "SATA Controller" --port 0 --device 0 --type hdd --medium elgg.vdi</code> |
| − | #* <code> VBoxManage storagectl | + | #* <code> VBoxManage storagectl elgg --name "IDE Controller" --add ide --controller PIIX4</code> |
#* set the nat rules (ports): | #* set the nat rules (ports): | ||
| − | #*: <code> VBoxManage modifyvm | + | #*: <code> VBoxManage modifyvm elgg --natpf1 "ssh,tcp,,15022,,22"</code> |
| − | #*: <code> VBoxManage modifyvm | + | #*: <code> VBoxManage modifyvm elgg --natpf1 "apache,tcp,,15080,,80"</code> |
| − | + | ||
# optional - set VRDE port: | # optional - set VRDE port: | ||
| − | #* <code>VBoxManage modifyvm | + | #* <code>VBoxManage modifyvm elgg --vrdeport 3389</code> (Note: 3389 is the default port anyway) |
# start the VM | # start the VM | ||
| − | #: <code>VBoxHeadless -s | + | #: <code>VBoxHeadless -s elgg --vrde on &</code> |
#: the VM will listen on port 3389 | #: the VM will listen on port 3389 | ||
# The following step do not seem to be necessary with Ubuntu 14.04 and new VirtualBox - however, are necesary for 12.04. But if so: connect with VRD and adjust network card settings (remember the existing VM have an old password) | # The following step do not seem to be necessary with Ubuntu 14.04 and new VirtualBox - however, are necesary for 12.04. But if so: connect with VRD and adjust network card settings (remember the existing VM have an old password) | ||
| Line 29: | Line 30: | ||
#* reboot | #* reboot | ||
#* check if ssh connection works | #* check if ssh connection works | ||
| − | + | ||
| − | + | == Elgg Setup == | |
| − | + | ||
| − | + | ||
Revision as of 13:54, 5 September 2014
>> return to Cedeus_IDE
steps performed:
- copying basicubunutu1404.vdi file and renaming to elgg.vdi
Elgg VM setup
- creating the tilestream VM on CedeusDB (ip.18):
-
VBoxManage createvm --name elgg --ostype Ubuntu_64 --register -
VBoxManage modifyvm elgg --memory 4096 -
VBoxManage modifyvm elgg --cpus 4 -
VBoxManage modifyvm elgg --nic1 nat -
VBoxManage storagectl elgg --name "SATA Controller" --add sata --controller IntelAhci - assign the (old) disk image a new uuid
-
VBoxManage internalcommands sethduuid elgg.vdi
-
- attach the (old) disk image:
-
VBoxManage storageattach "elgg" --storagectl "SATA Controller" --port 0 --device 0 --type hdd --medium elgg.vdi
-
-
VBoxManage storagectl elgg --name "IDE Controller" --add ide --controller PIIX4 - set the nat rules (ports):
-
VBoxManage modifyvm elgg --natpf1 "ssh,tcp,,15022,,22" -
VBoxManage modifyvm elgg --natpf1 "apache,tcp,,15080,,80"
-
-
- optional - set VRDE port:
-
VBoxManage modifyvm elgg --vrdeport 3389(Note: 3389 is the default port anyway)
-
- start the VM
-
VBoxHeadless -s elgg --vrde on & - the VM will listen on port 3389
-
- The following step do not seem to be necessary with Ubuntu 14.04 and new VirtualBox - however, are necesary for 12.04. But if so: connect with VRD and adjust network card settings (remember the existing VM have an old password)
- open /etc/udev/rules.d/70-persistent-net.rules and comment out existing network adapters
- reboot
- check if ssh connection works
